Skip to content
Decovive
Recycling & Upcycling

60 Indoor Pallet Projects That Furnish a Whole House

3 Shares
60 Indoor Pallet Projects That Furnish a Whole House

Pallets usually arrive by accident, under a delivery or stacked behind a shop, and then sit in a corner until someone calls them firewood. Look at one a little longer and you see something else: a frame of dry boards, blocks and stringers that was made to carry weight. Stack two and you have the base of a sofa. Stand one on its end and you have the back of a bookcase.

The 60 pallet projects below move through the house room by room, from living room seating and bedroom storage to the pantry, the bathroom wall, the mudroom and a long run of children's corners. Some use whole pallets with almost no cutting, others take the boards apart and rebuild them into hearts, houses and arches. Read the short guide first, because the right pallet, the right fixings and enough curing time decide whether a piece lasts a season or a decade.

Table of Contents
  1. Before You Build: Pallets, Joints and Finishes
  2. Read the stamp before a pallet comes home
  3. Take boards apart without splitting them
  4. Clean, dry and sand
  5. Screws carry the load, glue keeps joints tight
  6. Paint, stain and seal
  7. Hardware that does the heavy lifting
  8. Sofas, Daybeds and Reading Nooks
  9. 1. Rose Painted Chaise with a Folk Flower Border
  10. 2. Loveseat with Ribbon Tied Back Cushions
  11. 3. L Shaped Sectional with a Rolling Glass Table
  12. 4. White Daybed with a Slatted Back and Arm
  13. 5. Daybed with Drawers and Cubby Arms
  14. 6. Low Floor Sofa for a Boho Corner
  15. 7. Alcove Daybed with a Slatted Canopy
  16. 8. Arched Library Nook over a Pallet Seat
  17. Coffee Tables, Side Tables and Cabinets
  18. 9. Whitewashed Double Pallet Coffee Table
  19. 10. Two Tone Pink Coffee Table with a Blanket Shelf
  20. 11. Gray Washed Table with Pull Out Trays
  21. 12. Walnut Stained Bedside Table with a Slide Out Tray
  22. 13. Half Round Cabinet with a Scalloped Band
  23. Beds, Wardrobes and Bedroom Storage
  24. 14. Blue Canopy Bed with Bookshelf Posts
  25. 15. Storage Wall That Frames the Bed
  26. 16. Plum Bed with a Corner Headboard
  27. 17. Open Wardrobe with a Hanging Rail
  28. 18. Linen Cabinet with a Shelved Door
  29. Shelves, Bookcases and Media Walls
  30. 19. Stepped Bookcase in Raw Pallet Wood
  31. 20. Offset Cube Plant Stand
  32. 21. Whitewashed TV Wall with Side Shelves
  33. 22. Corner Shelf from Two White Pallets
  34. 23. Bookcase Room Divider
  35. 24. Upright Rack for Comics and Magazines
  36. Kitchen, Dining and Hosting
  37. 25. Three Tier Tea Station Shelf
  38. 26. Corner Banquette for a Breakfast Nook
  39. 27. Rustic Wine Bar Cabinet
  40. 28. Walk In Pantry with Pallet Board Shelves
  41. Entryways, Work and Hobby Spaces
  42. 29. Navy Mudroom Wall with a Boot Bench
  43. 30. Entry Lockers with Heart Cutouts
  44. 31. Slim Hallway Console with White Slats
  45. 32. Home Office Desk on Black Pallet Towers
  46. 33. Craft Room Wall and Rolling Worktable
  47. 34. Home Gym Storage Corner
  48. 35. Pet Corner with a Bed, Leash Rack and Raised Bowls
  49. Bathroom Shelves and Cabinets
  50. 36. Cream Towel Shelf with X Braced Sides
  51. 37. Hexagon Shelves on a Tall Panel
  52. 38. Towel Cubby Cabinet with a Center Bar
  53. 39. Little House Shelf for Soaps
  54. 40. Olive Cabinet with a Porthole Niche
  55. 41. Whitewashed Pallet Towel Rack with Hooks
  56. 42. Medicine Cabinet with a Mirror Door
  57. Kids' Rooms and Play Corners
  58. 43. Bunny Ears Reading Bench
  59. 44. Folding Gate for a Play Corner
  60. 45. Indoor Playhouse with a Slatted Roof
  61. 46. Playpen with a Hinged Front
  62. 47. Little Performance Stage
  63. 48. Heart Shelf in Lilac and Coral
  64. 49. Guitar Shaped Music Shelf
  65. 50. Dollhouse Bookcase
  66. 51. Bunny Face Toy Shelf
  67. 52. House Frame Floor Bed
  68. 53. Homework Desk on Coral Pallets
  69. 54. Reading House with Book Ledges
  70. 55. Children's Art Display Wall
  71. 56. Dress Up Wardrobe with a Mirror
  72. Wall Accents and Living Green
  73. 57. Diamond Shelf with Nested Frames
  74. 58. Leaning Pallet Christmas Tree
  75. 59. Wall of Flower Crates
  76. 60. Living Room Divider with a Climbing Planter
  77. Safety Notes for Pallet Furniture

Before You Build: Pallets, Joints and Finishes

Read the stamp before a pallet comes home

Look on the side of a block or stringer for a small box with a wheat ear symbol. That is the IPPC mark, and the letters beside the country code show how the wood was treated. HT means heat treated in a kiln with no chemicals, which is the code you want for anything that lives indoors. DB means the bark was removed and KD means kiln dried; both are fine. MB means the wood was fumigated with methyl bromide, a toxic pesticide, so leave that pallet where it is and never cut, sand or burn it. Euro pallets branded EPAL in an oval on the corner block have been heat treated as standard since 2010, which makes them an easy pick in Europe.

Skip pallets with no mark at all for beds, children's pieces and anything near food. Pass on boards with dark oily stains, a chemical smell, mold or crumbling wood, and leave brightly painted blue or red pallets alone, as those normally belong to rental pools and are not free to take.

Take boards apart without splitting them

Pallet nails are ringed or twisted so they grip under vibration, which is why prying boards straight up tends to crack them. The cleanest method is a reciprocating saw with a bimetal blade: lift the board a few millimeters with a flat pry bar, slide the blade into the gap and cut the nails between board and stringer. Punch the leftover nail stubs out with a nail set before you saw or sand that board. If you prefer hand tools, a long pallet breaker that hooks over two stringers spreads the force and splits far fewer boards than a short crowbar. Gloves, eye protection and closed shoes are not optional here, because nail heads snap and fly.

Clean, dry and sand

Scrub the wood with warm soapy water and a stiff brush, then let it dry completely indoors for several days before you build, since damp boards shrink and twist once they are fixed in place. Sand with 80 grit to remove splinters and grime, move to 120, and finish at 180 on anything that touches skin, such as seats, bed rails, shelves at child height and table tops. Ease every edge slightly. Do the sanding outdoors or with a vacuum attached to the sander, and wear a fitted dust mask.

Screws carry the load, glue keeps joints tight

Frames that hold a person or a row of books should be joined with wood screws. Drill a pilot hole first, because dry pallet boards split easily near their ends, and choose screws that reach at least two thirds of the way into the second piece. A pocket hole jig hides screws on visible frames. Where boards meet face to face, such as a glued up top or a doubled shelf, add PVA wood glue as well. Standard yellow wood glue suits indoor pieces; for bathrooms, entry benches and anything that gets wiped often, choose a waterproof formula such as Titebond III. Clamp for 30 to 60 minutes and do not stress the joint for a full 24 hours. When you fix uneven reclaimed boards onto plywood as cladding, construction adhesive is the better choice because it fills the gaps a thin wood glue cannot bridge.

Paint, stain and seal

Most pallet wood is pine or spruce, and its knots push yellow resin through white and pastel paint, sometimes weeks after you finish. A shellac based primer such as Zinsser BIN, brushed over the knots or the whole piece, stops that bleed. Chalk paint gives the soft matte look seen on many of the painted pieces below; a white wash of thinned paint wiped back with a rag gives a bleached look while keeping the grain. Pine stains unevenly, so test on an offcut and use a wood conditioner or a gel stain for darker tones. If you want to push color further, these painted furniture ideas show how pattern changes a plain piece.

Seal anything that gets handled with a water based polyurethane, which stays clear over pale colors. Most can be recoated after about two hours and feel dry within three, but the film needs about a day before light use and roughly a week before heavy books, hot mugs or daily sitting. Two or three thin coats with a light 220 grit sanding between them hold up far better than one thick coat.

Hardware that does the heavy lifting

A few bought parts make pallet furniture safer and nicer to live with. Fit locking casters rated well above the weight of the piece and screw them into the solid blocks, not the thin deck boards. Glass tops should be tempered and rest on small clear bumpers. Tall pieces need an anti tip strap or bracket screwed into a wall stud, and every wall shelf needs fixings that suit the wall it hangs on. Drawer runners, sturdy hinges and magnetic catches cost little and turn a rough box into proper furniture.

Sofas, Daybeds and Reading Nooks

1. Rose Painted Chaise with a Folk Flower Border

Pallet wood chaise lounge with a dusty pink frame, hand painted floral border, pale pine slats and linen cushions with blue piping

A chaise wants a long frame and a firm seat, and pallet timber gives you both. On this one the posts, arms and side rails are painted a dusty rose, while the seat slats and backrest stay raw pale pine, so the two tones frame the linen cushions instead of competing with them. A hand painted ribbon of small flowers runs along the legs and rails and makes the piece look inherited rather than built last weekend.

Make the chair section and the footrest one continuous frame with two long side rails, then screw the slats across with a finger width gap so the cushions can breathe. Cut the rear posts at a slight angle for a reclined back. A stencil keeps the border neat; seal it with a matte water based polyurethane so it survives sliding and shoes. By a bedroom window or in a quiet corner of a cottage living room, it gives you a place to read with your feet up without the footprint of a sofa.

2. Loveseat with Ribbon Tied Back Cushions

Two stacked pallets forming a loveseat with cream seat cushions, back cushions hung on blue ribbon ties and a terracotta painted front band with a wavy line

Two pallets stacked flat put the seat at a height most adults find comfortable once a cushion is added, and a slatted back panel screwed behind closes the frame. The charm sits in two details. The front stringer of the lower pallet is painted terracotta with a wavy mustard line and small dots, and the back cushions hang from the top rail on pale blue fabric ties.

Hanging cushions are a smart answer to uneven back slats, since they cover them completely and lift off for washing. Sew the ties into the cushion seam rather than pinning them. Join the two pallets through their blocks with long screws and attach the back with angle brackets on the inside where nobody sees them. The result is small enough for a bedroom wall, a landing or a narrow hallway where a full sofa would crowd the space.

3. L Shaped Sectional with a Rolling Glass Table

L shaped pallet sectional sofa with mustard and cream mattress cushions and a pallet coffee table on casters with a glass top and candles

Long runs of seating are where pallets save the most money. Each arm of this L is two pallets stacked, covered with thick mattress style cushions in mustard and cream, with loose back cushions leaning against the wall. A single pallet on casters with a glass panel on top acts as the coffee table and rolls out of the way when you need floor space.

Tie the pallets of each run together underneath with flat steel mending plates so the seats never creep apart, and add felt pads or rubber feet to protect the floor. Choose foam at least 4 inches (10 cm) thick; anything thinner lets you feel every slat. Warm ochre and mustard soften all that raw wood, and the low profile suits a retro room with an arc lamp and a windowsill full of plants.

4. White Daybed with a Slatted Back and Arm

White painted pallet daybed with a base of stacked pallets, an upright pallet backrest and side arm, a tufted mattress and striped pillows

Paint a pallet white and it stops looking like a warehouse and starts looking like cottage furniture. Here a stack of pallets forms the base, one stands behind as a backrest and a cut down pallet makes the side arm, all in the same soft white. A tufted mattress and striped pillows make it soft enough for an afternoon nap, and a wicker basket at the foot keeps a quilt nearby.

Prime with a stain blocking primer before the white paint, or the knots will show through within weeks. Bolt the upright pallets to the base with carriage bolts or long structural screws so the back stays solid when someone leans into it. A single mattress or futon pad works better than loose cushions, because it stays put and turns the daybed into a guest bed without any rearranging.

5. Daybed with Drawers and Cubby Arms

Gray washed pallet wood daybed with three drawers in the base, stepped cubby shelves as arms, a lilac tasseled throw and colorful shell shaped pillows

This piece shows how far pallet boards can go once they are taken apart. The base is a long box with three drawers, faced in planks with a soft gray wash, and each arm is a stepped tower of open cubbies for small books, baskets and trinkets. A camel cushion, a lilac throw finished with sage tassels and a pile of shell and scallop pillows bring a joyful mood to a teal wall.

Build the base as a frame from stringers, clad it with boards, and hang the drawers on full extension metal runners so they slide easily even when full of blankets. A sheet of plywood under the seat cushion gives an even, firm platform. Sand the inside corners of the cubbies carefully, since hands reach into them every day. If this kind of bright, layered color is your style, the dopamine living room ideas are full of it.

6. Low Floor Sofa for a Boho Corner

Two pallets side by side forming a low floor sofa with blue cushions and kilim and ikat pillows, a red shag rug and a round wooden stool table

Not every pallet sofa needs height. Two pallets set side by side, only one layer high, keep the seat close to the floor, which suits a laid back room built around a deep shag rug, big leafy plants and a stool used as a side table. Blue seat cushions sit on the pallets, and a lineup of ikat, stripe and kilim pillows leans against the wall.

Because the frame is so low, use thicker seat cushions, around 6 inches (15 cm), so standing up stays easy. Leave the wood its natural color, sand the top boards smooth and finish them with a clear matte sealer. A pair of mending plates across the joint keeps the two pallets aligned, so no gap opens between the cushions. A floating shelf above with trailing pothos ties the corner together.

7. Alcove Daybed with a Slatted Canopy

Pallet daybed fitted into an arched alcove with a slatted back, an overhanging slatted canopy, a navy cushion and rust and gray pillows

An empty alcove becomes a nook with a pallet base, a slatted back and a short slatted canopy that reaches over the seat like a small pergola. The wood has a pale, slightly gray tone that sits calmly against plaster colored walls, and a navy cushion with rust and gray pillows adds just enough color.

Measure the alcove at the bottom, middle and top before cutting, because old walls are rarely square, and build the base a little narrower so it slides in. Screw the back frame into the wall with suitable plugs; that also steadies the canopy. A side table no taller than the seat keeps a cup within reach. Nooks like this give a bedroom or landing a dedicated spot for rest without taking floor space from anything else.

8. Arched Library Nook over a Pallet Seat

Arched pallet wood bookcase filled with books wrapping around a corner seat of stacked pallets with cream cushions and a brown throw

Book lovers will understand this one at a glance. A tall arch of pallet wood wraps around curved shelves packed with books, and below it a corner seat of stacked pallets holds deep cream cushions and a soft throw. Even the top of the arch carries a stack of books, and a small brass lamp sits on a shelf inside for evening reading.

The arch is the demanding part. Cut it in short segments from wide boards or from plywood faced with pallet boards, join the segments with glue and screws from behind, and fix the shelves to a strong back frame rather than to the curve alone. A wall of books is heavy, so anchor the frame to studs near the top. For a sloped ceiling version, the attic reading nook ideas show other ways to frame a corner like this.

Coffee Tables, Side Tables and Cabinets

9. Whitewashed Double Pallet Coffee Table

Two stacked whitewashed pallets used as a coffee table with a glass top, magazines and a small trailing plant tucked between the layers

Two pallets stacked and brushed with a rough whitewash make about the quickest coffee table you can build, and the glass top lets the slat pattern show through. The gap between the layers turns into a shelf for magazines, or for a small trailing plant that spills over the side.

Leave the paint slightly uneven and sand the edges back so a little wood peeks through. Order tempered glass cut to the exact size of the top with polished edges, and stick clear silicone bumpers on the slats so the glass sits level and quiet. Screw the two pallets together through their blocks first; otherwise the top layer shifts the first time someone puts their feet up.

10. Two Tone Pink Coffee Table with a Blanket Shelf

Pallet coffee table with pink painted blocks and stringers, cream deck boards, a glass top and a folded blanket stored between the layers

Color changes everything on a pallet. Here the blocks and stringers are painted rose pink while the deck boards stay cream, so the structure of the pallet becomes a pattern of its own. A glass top protects the paint, and a folded patterned blanket waits on the lower deck for a movie night.

Paint the two colors before assembly, or tape them off with care afterward; the effect depends on crisp lines. A durable furniture paint finished with water based polyurethane handles mugs and feet. Next to a tan leather sofa and a multicolored rug, the soft pink keeps a bright room from feeling loud.

11. Gray Washed Table with Pull Out Trays

Gray washed pallet coffee table with two shallow drawers pulled out of the openings, a black teapot, pampas grass and a cream sofa behind

The open spaces inside a pallet are wasted on most coffee tables. In this one they hold shallow trays that slide out between the blocks, one for coasters, one for remotes or a notebook. The gray wash finish fits a calm Scandinavian boho room with rattan, woven wall baskets and pampas grass.

Build each tray as a simple open box a few millimeters smaller than the opening. Let it run on the board below and rub candle wax along the bottom edges so it slides easily, then glue a thin stop strip at the back so it cannot be pulled out completely. Seal the inside of the trays too. For the wash itself, thin a gray paint with water, brush it on and wipe it back with a rag before it dries.

12. Walnut Stained Bedside Table with a Slide Out Tray

Dark walnut stained pallet wood bedside table with slatted sides and a slide out tray holding a red napkin beside a bed with patterned curtains

Pallet wood takes a dark stain beautifully, and this bedside table shows it. Slatted sides keep the piece light, and a slide out tray gives extra room for a teacup or an open book without cluttering the top. The deep walnut tone sits comfortably beside carved antique chairs and bold printed curtains.

Test the stain on an offcut first, because pine soaks up color unevenly; a wood conditioner applied before staining, or a gel stain, prevents blotches. Run the tray on wooden runners or small metal slides and add a stop block underneath. A satin polyurethane on the top protects it from glass rings.

13. Half Round Cabinet with a Scalloped Band

Half round cabinet with a pale pallet slat top, a pink and bronze scalloped painted band, blue washed side boards and a curved shelf holding a tureen and bowls

A half round cabinet fills a wall without the sharp corners that catch hips in a busy room. This one has a top of pale slats, blue washed boards on the sides, and a cream apron painted with pink and bronze scallops that gives it a sweet farmhouse face. Inside, a curved shelf carries a tureen and nested bowls.

The curve comes from plywood rather than from the pallet boards. Cut two half circles of 3/4 inch (18 mm) plywood for the base and top frame, then glue and screw narrow upright boards around the front edge. Narrow strips follow a curve best, so rip wide boards to around 2 to 3 inches (5 to 7 cm). A thin sheet of 1/8 inch (3 mm) plywood bends easily for the inner back and the apron band. Glue the top slats edge to edge, cut them to shape with a jigsaw, and seal them, since this is where vases and cups will stand.

Beds, Wardrobes and Bedroom Storage

14. Blue Canopy Bed with Bookshelf Posts

Deep blue painted pallet canopy bed with upright pallet posts, a slatted pallet canopy overhead, side shelves of books, a clip lamp and baskets under the bed

A canopy bed usually calls for real carpentry, but this one is made mostly from whole pallets. Pallets laid flat form the base, pallets stood upright frame the head and both sides, and more pallets laid across the top create a wooden roof. Narrow shelves on the outer posts hold paperbacks, a clip lamp hangs at reading height, and wicker baskets slide into the openings under the bed.

Deep blue paint ties together the mix of wood tones and makes the whole frame look intentional. Because the canopy hangs over a sleeping person, it must be bolted to the posts, the posts bolted to each other and the frame fixed to the wall; nothing up there should simply rest in place. Use only sound boards overhead and keep the canopy light. Gingham bedding and books within reach make it a favorite for teenagers and night readers.

15. Storage Wall That Frames the Bed

Natural pallet wood storage wall with two tall side towers and a bridge of cabinets above a white bed, an open niche with folded linen and brown leather poufs

When a bedroom has no room for a wardrobe, build storage around the bed instead. Two tall towers and a bridge of cabinets above the headboard are clad in horizontal pallet boards, sanded and left pale. A small open niche in one tower stands in for a nightstand, and white bedding with brown leather poufs keeps the look clean and modern.

Build the cabinet boxes from plywood and use pallet boards purely as cladding, glued on with construction adhesive and pinned with brad nails. The structure stays strong and the boards just bring the texture. Screw the bridge cabinets into studs or masonry, and keep them for light things such as spare bedding and pillows rather than heavy boxes.

16. Plum Bed with a Corner Headboard

Plum painted pallet bed with a pallet headboard that wraps onto the side wall, paisley bedding, rust pillows and a cream crochet throw

A pallet bed frame is one of the most popular conversions, and the paint color sets the whole mood. This one is a deep plum with a gently worn finish, and its headboard turns the corner with an extra pallet along the side wall, which makes the bed feel tucked in. Paisley bedding, rust pillows and a cream crochet throw keep it warm and bohemian, while hanging plants and two small mirror balls add a playful touch.

For a double mattress, four standard pallets laid in two rows usually make one layer of base; measure your pallets against the mattress before you collect them. The open slats let air move under the mattress, which helps keep it dry. If the gaps between boards are wide, lay a thin board or a slatted bed base on top so the mattress is evenly supported, and round every corner you could catch with a shin at night.

17. Open Wardrobe with a Hanging Rail

Open pallet wardrobe with a wooden hanging rail holding shirts and a shawl, a column of slat shelves with folded textiles and a seagrass basket on a pallet base

A wardrobe does not always need doors. This open version stands on a pallet base, with upright pallet sides, a round wooden rail for hanging and a column of slat shelves for folded clothes and blankets. A seagrass basket at the bottom catches bags or shoes, and the deep purple wall behind turns everyday clothes into part of the decor.

Pick a hanging rail thick enough not to sag, at least 1 1/4 inches (32 mm), and support it with brackets at both ends. Shelves should rest on wooden cleats screwed to the uprights, never on nails. Since the unit is tall and open at the front, fix it to the wall at the top. It suits a guest room, a studio or a small bedroom where a closed wardrobe would feel heavy.

18. Linen Cabinet with a Shelved Door

Cream painted pallet linen cabinet with folded throws on shelves, two drawers at the bottom and an open door with shelves holding a vase, jars and a rolled throw

Throws and blankets eat space, and this cream cabinet stores them with a clever trick: the door carries shelves of its own. The main body holds folded and rolled throws above two deep drawers, while narrow ledges on the inside of the door take a vase, a lidded jar and one more rolled throw. The whole unit sits on a pallet base.

A door loaded with shelves is heavy, so use a continuous piano hinge or three solid butt hinges, and give each door shelf a raised lip so nothing slides off as it swings. Keep the heaviest items low and fix the top to the wall. In a satin cream finish, it fits a living room as easily as a bedroom.

Shelves, Bookcases and Media Walls

19. Stepped Bookcase in Raw Pallet Wood

Stepped asymmetric pallet wood bookcase with shelves at different heights holding books, a stone bowl, vases and a basket in front of a black and white gallery wall

Staggered shelves feel more relaxed than a straight bookcase and give you openings of different heights for books, vases and sculptural objects. This one uses thick pallet boards and blocks in their natural color, with a wide lower section and smaller stepped boxes on top, set under a gallery of black and white prints.

Line up the vertical supports from one level to the next so the weight travels straight down to the base, and screw the shelves from below through pilot holes. Raw wood looks right here, but a coat of clear matte polyurethane keeps it from snagging fabric and soaking up dust. Style it with a few larger objects rather than many small ones, so the stepped outline stays visible.

20. Offset Cube Plant Stand

Two chunky open pallet wood cubes stacked off center on a low pallet base, a pothos in the upper cube and two rustic vases in the lower one

Two open boxes stacked off center on a low pallet base make a shelf that reads almost like sculpture. The upper cube frames a pothos in a weathered pot and the lower one holds two rustic vases. The chunky frames are built from thick pallet timber, so the piece feels solid even though it is small.

Glue and screw each cube, hiding end grain where you can, and sand the faces well, because thick reclaimed timber often has deep cracks. Join the upper cube to the lower one with screws from inside so it cannot slide. Put a saucer under any plant pot, since water rings mark unsealed wood quickly, and remember that pothos is toxic to cats and dogs.

21. Whitewashed TV Wall with Side Shelves

Whitewashed upright pallets behind a TV with short shelves of books on both sides and a low pallet console with seagrass baskets below

Instead of a bulky media unit, this living room uses upright whitewashed pallets as a backdrop for the screen, with short shelves on both sides for books and a low console of stacked pallets below. Seagrass baskets slide into the console openings and hide cables, remotes and games.

Fix the upright pallets to the wall through the stringers into studs or masonry. If the TV stands on the console, push it back from the edge and secure it with an anti tip strap; if you would rather hang it, use a proper wall bracket fixed to the wall itself, not to the pallets. A hole through a deck board behind the screen lets cables disappear neatly. The soft whitewash keeps a neutral room bright.

22. Corner Shelf from Two White Pallets

Two white painted pallets meeting in a room corner with natural wood shelves on black brackets holding vases, framed photos, books and potted plants

Corners are hard to furnish, and two pallets meeting at a right angle turn one into a display wall. The pallets are painted white, and natural wood shelves rest on black steel brackets at three levels, carrying cream vases, framed photos, books and small plants.

Screw the two pallets together along the corner edge and fix each one to its wall. The stringers are the best place for the bracket screws, since the deck boards are thin. The mix of white back, warm shelves and black metal looks crisp in a Scandinavian room, and a large floor cushion beside a fiddle leaf fig makes the corner a quiet place to sit.

23. Bookcase Room Divider

Pallets standing side by side as a tall bookcase room divider filled with books and pottery, with trailing plants along the top beside a small dining table

In an open plan room, a bookcase can act as a wall. Several pallets stand side by side, two levels high, fitted with shelves for books and pottery, and a row of trailing plants runs along the top. The unit separates the sofa area from a small dining table without blocking light.

Loaded with books, a freestanding divider becomes top heavy. Bolt the pallets to each other, give the base extra depth, and fix one end to a wall or the ceiling with a bracket. Keep heavy books on the lowest shelves and lighter objects at the top. A matte clear finish on the honey colored wood looks warm against pine floors and lamplight.

24. Upright Rack for Comics and Magazines

Single upright pallet with narrow ledges holding comic books and magazines face out beside an armchair with a plaid throw and a brass floor lamp

Comics, picture books and magazines look better with their covers facing out, and a single pallet stood upright becomes a display rack with very little work. Narrow ledges run across the slats at even intervals, each with a small front lip so the issues lean back safely.

Cut the ledges from deck boards and glue a thin strip along the front edge as the lip. Space the rows to suit your tallest issues. The rack is tall and narrow, so anchor the top to the wall. An armchair, a floor lamp and a warm throw beside it are all a reading corner needs.

Kitchen, Dining and Hosting

25. Three Tier Tea Station Shelf

Cream pallet shelf unit with sage green slatted shelves holding a teapot tray, colorful mugs, a fruit bowl, a lidded jar and a woven basket

A small shelf near the kitchen or the sofa keeps mugs, a teapot and snacks together in one place. This one has a cream frame with three slatted shelves painted sage green, so the slats show up as stripes. A rattan tray on top holds the teapot and cups, the middle shelf takes mugs and a bowl of fruit, and the bottom keeps a lidded jar and a basket of napkins.

Seal everything with a wipeable water based polyurethane, since tea drips are guaranteed. Keep loose cups on a tray so they cannot slip between the slats, and fit a narrow lip along the back of each shelf. Against a teal wall, the two soft colors make a bright little café corner.

26. Corner Banquette for a Breakfast Nook

L shaped kitchen banquette of stacked terracotta painted pallets with pallet backrests, cream cushions, striped pillows and a round pedestal table with bentwood chairs

Built in seating makes a small kitchen feel like a café, and pallets make it affordable. Two runs of stacked pallets painted terracotta form an L along the walls, with upright pallets behind as backrests. Cream seat cushions, striped pillows and a round pedestal table with bentwood chairs complete the nook.

Plan the seat height around the table: about 18 inches (45 cm) including the cushion suits a standard dining table. Choose cushion covers with zippers so they can be washed. A hard wearing enamel or a sealed paint copes with shoes and chair legs. A round table works best in a corner bench, because nobody has to squeeze past a sharp corner to sit down.

27. Rustic Wine Bar Cabinet

Dark stained pallet wood bar cabinet with angled slats holding wine bottles on their sides, wine glasses hanging under the top and bottles and a decanter on top

For anyone who entertains, a cabinet like this keeps the whole bar in one place. The two side sections have angled slats that hold bottles on their sides, wine glasses hang upside down from a rack under the top, and the top itself carries a decanter, glasses on a tray and a few bottles ready to open.

Tilt each bottle slat slightly back so bottles cannot roll forward, and check the spacing with a real bottle before fixing. The glass rack is two strips of wood with a slot between them, sized to the stem. A dark stain sealed with polyurethane lets spills wipe off. Keep the cabinet away from radiators and sunny windows, since heat and light are hard on wine.

28. Walk In Pantry with Pallet Board Shelves

Walk in pantry with pallet board shelves on three walls holding glass jars of pasta, grains and spices, baskets of potatoes and a wooden step stool

Open shelves make a pantry easier to use than one full of closed cupboards, because you see every jar at once. Here pallet boards run along three walls from floor to ceiling, holding glass jars of pasta, rice, beans and spices, with baskets of potatoes on the floor and a wooden step stool for the top rows.

For any surface near food, use only HT stamped pallets, sand the boards smooth and seal them, and keep the food itself in closed jars. Glass jars add up to serious weight, so place shelf supports close together, around every 16 to 24 inches (40 to 60 cm), and screw them into studs. Store the heaviest jars at waist height to save your back.

Entryways, Work and Hobby Spaces

29. Navy Mudroom Wall with a Boot Bench

Navy painted pallets covering an entry wall with brass hooks holding coats and a scarf, and a bench of pallet boxes with boots and wicker baskets in the cubbies

Entryways take a beating, and pallets are tough enough for the job. Navy painted pallets cover the wall up to the ceiling, brass hooks hold coats and scarves, and a bench made from pallet boxes has open cubbies for boots and wicker baskets of hats and gloves.

Fix the wall pallets into studs and screw the hooks into the solid stringers rather than the thin slats. Wet boots bring water and grit, so finish the bench with a hard wearing exterior varnish. Open cubbies let boots dry. For more ways to sort a busy home, the upcycled storage ideas are worth a look.

30. Entry Lockers with Heart Cutouts

Locker style pallet cabinets in red and natural wood with heart shaped cutouts, one door open showing coats and boots, and a long pallet bench with a striped cushion

These locker style cabinets mix red painted and natural wood doors in a checkerboard, and each upper door has a heart cut into it. One locker stands open to show coats on hooks and boots on the floor. In front, a long pallet bench with a striped cushion gives everyone a place to pull shoes on.

Drill a starter hole inside each heart, cut the shape with a jigsaw and sand the edges round; the cutouts also let air into the lockers. Fit sturdy hinges and magnetic catches, and fix the whole row to the wall, especially if children open the doors. Assign one locker per person and the morning rush gets noticeably calmer.

31. Slim Hallway Console with White Slats

Slim hallway console made of white painted upright pallet slats with a thick weathered wood top holding framed photos, a small lamp and a key dish

A narrow hallway still has room for a console if it is this slim. White upright slats form the front and sides, and a thick weathered board on top holds framed photos, a small lamp and a dish for keys. The contrast of crisp white and dark old wood gives it a relaxed cottage feel.

Keep the depth around 10 to 12 inches (25 to 30 cm) so the passage stays clear, and screw the top to the wall so the console cannot rock. Sand the top well and seal it, because keys and bags will scratch it daily. Run a cable for the lamp down behind the slats, where it disappears.

32. Home Office Desk on Black Pallet Towers

Home office desk with a thick wooden top resting on two towers of stacked black painted pallets holding books, and a pallet wall organizer with clipboards, scissors and small potted plants

Stacked pallets make desk legs that double as shelving. Here pallets laid flat form two black towers, and their openings hold books and files. A thick wooden worktop spans the towers, and above the desk a pallet on the wall works as an organizer with clipboards, scissors and small pots of herbs and succulents.

A standard pallet is about 5 1/2 inches (14 to 15 cm) high, so five in a stack usually lands close to desk height; check against your chair before you commit. Screw each tower together and to the worktop with brackets, and choose a worktop at least 1 1/4 inches (3 cm) thick so it does not bounce. Fix the wall pallet into studs and use S hooks for tools.

33. Craft Room Wall and Rolling Worktable

Lavender painted pallets covering a corner craft wall with hooks for scissors and ribbons, small crates of yarn, and a rolling worktable of stacked pallets with storage bins

Crafting takes a lot of small storage, and this room shows how pallets provide it. Lavender pallets cover two walls of a corner, carrying hooks for scissors, rulers and ribbons, small crates of yarn and narrow shelves of paint. In the middle, a worktable of stacked pallets on casters holds bins of supplies between its layers, with a patchwork of fabric squares on top.

Fit locking casters so the table stays still while you cut or sew, and cover the top with a smooth board or a cutting mat. The wall works like a giant pegboard: add hooks, crates and shelves wherever the next tool needs a home. A soft single color on the pallets keeps a room full of bright supplies from feeling chaotic.

34. Home Gym Storage Corner

Dark charcoal stained pallets lining a gym corner with shelves of kettlebells and dumbbells, hooks for resistance bands and orange foam rollers, and heavy kettlebells on the floor

Weights are heavy, awkward and always underfoot, and a pallet wall gives a home gym some order. Charcoal stained pallets line the corner, with shelves for kettlebells and dumbbells, hooks for resistance bands and jump ropes, and room for foam rollers. The heaviest kettlebells stay on the rubber floor.

This build needs more support than any other on the list. Shelves for weights should rest on steel brackets or thick wooden cleats screwed into studs, and the pallets themselves must be fixed to the wall. Keep the heaviest pieces on the floor or the lowest shelf, and check the boards for cracks every few months.

35. Pet Corner with a Bed, Leash Rack and Raised Bowls

Dark stained pallet pet bed with a gray cushion, an upright pallet with leashes and a hanging basket, and a small pallet riser holding two food bowls

Pets deserve a corner of their own too. A low bed of two stacked dark stained pallets carries a thick gray cushion, a pallet standing against the wall holds leashes and a hanging basket of toys, and a small pallet riser lifts the food and water bowls off the floor.

Sand every surface smooth so there are no splinters for paws or mouths, and use a water based finish that has fully cured before your pet moves in. Pick a cushion with a removable, washable cover. Raised bowls are more comfortable for larger dogs, and the riser keeps spilled water off the bed.

Bathroom Shelves and Cabinets

36. Cream Towel Shelf with X Braced Sides

Cream painted three tier pallet wood shelf with X braced sides holding folded towels, a woven basket, a potted plant and a bath brush next to a sink

A narrow shelf beside the sink keeps towels, a basket of spares and a plant together. This one is painted cream, with X braces on the sides and slatted shelves on three levels. The X braces are more than decoration; they stop the unit from racking sideways.

In a bathroom, seal every face, including the underside of the feet, with a water resistant polyurethane, and assemble with a waterproof glue. Lift it a little off the floor on small feet so the tiles can dry after mopping, and leave a finger gap between the unit and the wall for air. Folded white towels on cream wood look calm with hexagon tiles and a woven rug.

37. Hexagon Shelves on a Tall Panel

Tall taupe painted pallet board panel with three stacked hexagon shelves holding plants and a lidded basket, and two small ledges with a soap dish, jar and rolled towel

Three hexagon boxes stacked on a tall panel of vertical boards hold trailing plants and a lidded basket, with two small ledges below for a soap dish, a jar and a rolled towel. The soft taupe finish suits a bathroom of cream tiles and warm wood cabinets.

Each hexagon is six equal pieces with both ends cut at 30 degrees, so the joints close into 120 degree corners. Glue them with a waterproof wood glue and tape the shape tight while it sets, then screw each box to the panel from behind. Humidity loving plants such as pothos and ferns enjoy a bathroom, but water them in the sink so drips stay off the wood.

38. Towel Cubby Cabinet with a Center Bar

Weathered pallet wood wall cabinet with narrow cubbies of rolled towels on both sides, a wooden bar with a hanging hand towel in the middle and a small crate tray below

This wall cabinet gives every towel its own place. Narrow cubbies on both sides hold rolled bath towels, a wooden bar across the middle carries a hand towel, and a small crate at the bottom keeps a brush and a lidded jar. The weathered gray brown wood hides water spots well.

Build the outer box from pallet boards, divide the side columns with short shelves, and back it with the original slats. A French cleat, two strips cut at 45 degrees with one screwed to the wall and one to the cabinet, makes hanging it strong and easy. Size the cubbies to your rolled towels before cutting the dividers.

39. Little House Shelf for Soaps

Sage green pallet wood wall shelf shaped like a small house with a slatted roof, holding amber pump bottles and bars of soap, with a pothos trailing beside it

Small bathrooms rarely have space for a cabinet, but they nearly always have a bare patch of wall above the basin. A shelf shaped like a little house fills it with character: a slatted roof on top, an open frame in the middle and a crate box at the bottom for pump bottles and soap. Sage green, dry brushed so the grain still shows, looks fresh against cream tiles and a trailing plant.

Cut the two gable boards at 45 degrees where they meet at the peak, then fix short slats across them with a slight overlap so they read like shingles. Give the crate a solid floor so bottles cannot slip between slats. Seal it with at least two coats of water resistant polyurethane, since wet hands reach for it all day, and hang it with screws and plugs made for tiled walls.

40. Olive Cabinet with a Porthole Niche

Olive green painted pallet slat wall cabinet with a round porthole niche holding a jar and a plant, a shelf of rolled towels and a slot with a waffle hand towel

One round opening is enough to turn a plain slatted box into the focal point of a bathroom. This olive green cabinet has a porthole niche at the top for a glass jar and a plant, an open shelf of rolled towels in the middle and a long slot near the bottom where a hand towel hangs over a bar. Olive with warm wood and white ceramics gives a quiet, natural spa feeling.

Assemble the front first, draw the circle with a compass or a pot lid and cut it with a jigsaw, starting from a drilled hole. A thin strip of bendable plywood glued around the inside of the opening gives the porthole a clean rim. Round the edges of the towel slot so cotton does not snag, and keep heavier items on the middle shelf, closest to the wall fixings.

41. Whitewashed Pallet Towel Rack with Hooks

Whitewashed pallet hung on a tiled bathroom wall with two small shelves holding bottles and jars and three metal hooks with hanging linen towels above a bathtub

This is the quickest bathroom project in the collection: one pallet, washed in white and hung on the wall beside the tub. Two short shelves fit between the slats for bath oil, a pump bottle and jars of cotton, and three hooks along the bottom rail keep linen towels within reach of the bath.

Cut the shelves from leftover deck boards and rest them on small cleats so they cannot tilt. The hooks belong in the solid bottom stringer, where screws hold properly. A whitewash sealed with water based polyurethane keeps the faded, gentle look while protecting the wood from steam. If you like this softer style, the shabby chic bathroom ideas build on the same pastel, weathered palette.

42. Medicine Cabinet with a Mirror Door

Pallet wood bathroom wall cabinet with an EPAL brand on the side, shelves of toothbrushes and toiletries and an open rounded mirror door, with a small pallet planter shelf below

A medicine cabinet built from pallet wood hides toothbrushes, creams and cotton jars behind a mirror, so the counter stays clear. The EPAL brand on the side is left on purpose as a nod to the wood's past, and a small pallet box below the cabinet holds a few green plants above the basin.

Choose a mirror with a safety backing film, so broken glass stays in place, and set it into a solid wood frame rather than gluing it straight to slats. Two good hinges and a magnetic catch keep the door aligned. A mirror door puts weight on the front edge, so hang the cabinet on a French cleat or screws into studs, and seal the inner shelves, because toiletries always leak eventually.

Kids' Rooms and Play Corners

43. Bunny Ears Reading Bench

Pallet wood bench with a cream cushion and pink pillows set against a tall back shaped like bunny ears, with small shelves holding books and decor

A bench is useful; a bench framed by two giant bunny ears becomes the favorite spot in the room. Pallet boards fill the tall ear shapes behind a cushioned seat, and short shelves set inside the ears hold books, a small vase and a piece of coral. With pink ikat pillows and a lilac wall, it feels soft and sweet without tipping into babyish.

Draw the ears full size on paper, lay boards edge to edge over a plywood backer, trace the outline and cut it with a jigsaw. Thin strips glued around the edge hide the raw board ends. The back is tall, so fix it securely to the wall, because children will climb it. A lift up seat on soft close hinges turns the bench into a toy chest as well.

44. Folding Gate for a Play Corner

Folding pallet wood gate made of hinged slatted panels standing on wooden feet in front of a children's play table with toys and stuffed animals

Zoning a playroom helps toys stay in one area, and a folding fence of pallet slats does it with more warmth than a plastic barrier. Hinged panels on chunky wooden feet close off a corner with a little table, a basket of plush animals and a box of building blocks.

Join the panels with sturdy butt hinges and fix the two end panels to the walls so a toddler cannot push the fence over. Keep the gaps between slats no wider than about 2 3/8 inches (6 cm), so a small head or arm cannot pass through or become trapped, and avoid horizontal rails that work like ladder rungs on the inside. Treat this as a divider for supervised play; it is not a tested safety gate for stairs.

45. Indoor Playhouse with a Slatted Roof

Indoor pallet wood playhouse with a pitched slatted roof, open door and window openings, a cushion and toys inside, in a colorful room with a tiger painting

Every child wants a house inside the house. This one is built from weathered pallet boards with a pitched slatted roof, a wide doorway and open windows, raised slightly on pallet blocks. A woven mat, cushions, a plush rabbit and a wooden truck make it a ready hideout, and it suits an eclectic room full of art and color.

Build the walls as framed panels, screw them together at the corners and add the roof slats last, keeping the whole roof low and light. Sand the door and window openings until they feel completely smooth, since hands grab them constantly. A paint or clear coat labeled safe for toys is the right finish. For more storybook settings, browse these children's bedroom themes.

46. Playpen with a Hinged Front

Pallet wood playpen with slatted sides, a hinged front panel and pallet block feet, holding a patterned play mat, a plush bunny and wooden blocks

A slatted box raised on pallet block feet gives a crawling baby a safe, contained place to play on a soft patterned mat. The front panel swings open on hinges, so you can sit inside with the baby or lift them out without leaning over a high wall. In a white nursery under a sloped ceiling, the raw wood adds warmth.

Spacing matters more here than anywhere else in the house. Gaps between slats should not exceed about 2 3/8 inches (6 cm); if your boards sit farther apart, add extra slats or narrow strips between them. Put the latch on the outside, out of reach of small fingers, sand everything to 180 grit and use a toy safe finish. The mat should fill the floor completely, with no gap along the walls.

47. Little Performance Stage

Raised multi sided pallet wood stage with a front step, a guitar on a stand, costume bags and red velvet curtains against a red wall

Children who sing, dance or put on puppet shows light up when they have a stage. This low platform has angled corners, a wide front step and boards in mixed weathered tones, framed by red velvet curtains. A guitar on its stand and fabric bags of crowns and masks wait for the next performance, which makes the corner an invitation to play pretend.

Build a frame from stringers with joists no more than 16 inches (40 cm) apart and screw the deck boards across them, so the floor does not bounce under jumping feet. Keep the platform low, one step is plenty, and round the outer corners. A thick rug in front cushions the inevitable leap off the edge.

48. Heart Shelf in Lilac and Coral

Heart shaped pallet wood wall shelf painted lilac with coral corners, small inner shelves holding a teddy bear and a cloud pillow, on a black and white striped wall

Bold striped walls need simple shapes, and a heart outline holds its own against them. This one is painted lilac with coral pieces at the corners, and small inner shelves give a teddy bear and a cloud pillow their own spots.

The heart is made entirely of straight pieces with angled ends, so no curved cutting is needed. Lay the shape out on the floor first, mark each angle where the pieces meet, then glue and screw the joints and add the inner shelves last. Hang it on two strong fixings and place it above the height of a climbing child. The wall shelf designs collection has more shapes for small walls.

49. Guitar Shaped Music Shelf

Guitar shaped pallet wood wall shelf in navy and coral with a round sound hole ring, a slatted neck with wooden tuning pegs and a small pocket holding maracas

A guitar made from pallet boards turns a bare wall into a music corner. The body is navy with a coral lower bout, the neck is a column of pale slats, two wooden knobs act as tuning pegs and a small box on the body holds a pair of maracas. It brings a playful theme to the room while still storing something.

Lay boards side by side, glue a thin plywood sheet across the back, then trace the guitar outline and cut it with a jigsaw. A ring cut from a wider board forms the sound hole. The little pocket works for shakers, hair clips or pencils. Since children will reach into it, screw the guitar firmly into the wall at two points at least.

50. Dollhouse Bookcase

Pallet bookcase shaped like a dollhouse with a pitched white slatted roof, coral and blue painted back slats and three shelves holding toy furniture and stuffed animals

A bookcase shaped like a dollhouse does two jobs: it stores toys and it becomes the toy. White frames and a pitched slatted roof outline the house, while the back walls are painted coral and blue so each shelf reads as a separate room for miniature furniture, plush animals and small crates.

Start with an upright pallet, add a solid floor at each level and build the roof from two angled rafters with slats laid across. Painting the back slats before assembly keeps the color lines crisp. Children treat shelves like a ladder, so anchor the top to the wall and keep the heaviest toys on the ground floor.

51. Bunny Face Toy Shelf

Cream painted pallet wood toy shelf with pink bunny ears, a painted bunny face, a ledge with wooden blocks and a fabric pocket holding a toy carrot

Low storage teaches toddlers to tidy up on their own, and a friendly face makes them want to. This cream shelf has two pink ears, a simple painted bunny face, a ledge for wooden blocks and a canvas pocket across the front for soft toys.

Cut each ear from a single board and round the tips generously. Paint the face with a fine brush or a stencil, and fix the canvas pocket with upholstery tacks or screws through a thin wooden strip. Even a low shelf should be fixed to the wall, and a toy safe finish is right for anything little mouths might find.

52. House Frame Floor Bed

House shaped pallet wood floor bed frame with a peaked roof outline and chimney on a low pallet base, a white mattress and a pom pom garland

The house shaped floor bed is a Montessori favorite, because it lets a small child climb in and out alone, and pallets make it far cheaper to build. A frame with a peaked roof outline and a little chimney stands over a low pallet base, side rails keep the mattress in place, and a pom pom garland is strung along the roof beam.

Keep the base low and the mattress snug, with no gap between mattress and frame where a child could slip. Use thick timber for the roof frame, screw every joint and sand the posts until they feel like furniture. Anything hung from the frame should be short and fixed tight at both ends, so nothing can loop around a sleeping child.

53. Homework Desk on Coral Pallets

Kids homework desk with a white top on stacked coral painted pallets with EPAL brands, two wooden stools and a pallet wall shelf with books and hanging pencil cups

Two children can work side by side at this desk. Stacked pallets painted coral form the base, a smooth white top gives a clean writing surface and two wooden stools slide underneath. On the wall above, a pallet holds a row of books and a rail of metal cups for pencils and markers, which keeps the desk itself clear.

Leave the EPAL brands showing if you like the industrial touch; paint softens them without hiding them. Screw the pallets together and the top to the pallets. Check the height against the stools and plan for growth, since an adjustable chair lasts longer than a fixed stool. A lamp with a flexible arm completes the study corner. For more ways to plan a shared room, explore these kids room ideas for play, storage and learning.

54. Reading House with Book Ledges

Whitewashed pallet reading house with a pitched roof, a small window, book ledges on the walls, a green mattress, cushions, bunting and a mushroom lamp

Where the playhouse is for games, this house is for quiet time. It sits on a pallet base topped with a green mattress, and whitewashed pallet walls rise to a pitched roof with a small window. Ledges inside display picture books face out, so children pick by cover, and cushions, a triangle bunting and a mushroom lamp make it hard to leave.

Set the ledges at the child's sitting eye level and give each one a lip. Battery lamps are safer than plug in ones inside a small wooden space. Whitewash followed by a toy safe clear coat keeps the wood light and smooth to the touch.

55. Children's Art Display Wall

Two whitewashed pallets on a wall with twine lines and wooden clothespins holding children's drawings, above a floating pallet shelf with jars of crayons

Children's drawings deserve better than the fridge door. Two whitewashed pallets mounted side by side carry lines of twine with wooden clothespins, so new artwork goes up in seconds and the wall becomes a gallery that changes every week. Below, a pallet fixed flat to the wall works as a shelf for jars of crayons and colored pencils.

Tie the twine tightly between screw eyes set into the stringers, and screw the pallets into studs. If children are likely to sit on the lower pallet, support it with heavy duty brackets underneath. A playroom, hallway or kitchen wall all suit this, anywhere the family walks past often.

56. Dress Up Wardrobe with a Mirror

Lilac painted pallet wood dress up wardrobe with a rail of costumes, a full length mirror panel, a pallet top shelf with crowns and a hat, and shoes on the base

Costumes need a home of their own, and this lilac wardrobe gives them one. A low rail holds dresses, capes and tutus, a full length mirror stands beside it for checking the look, and a pallet on top displays crowns and a hat. Shoes line up on the pallet base with a basket for accessories.

Use an acrylic mirror or one with a safety film on the back; plain glass does not belong in a play space. Fix the frame to the wall, as a child swinging on the rail can pull a tall unit forward. Hang the rail at a height the children can reach on their own, so dressing up and tidying up both happen without help.

Wall Accents and Living Green

57. Diamond Shelf with Nested Frames

Diamond shaped pallet wood wall shelf made of nested frames with a gray wash, holding small wooden houses, a patterned pot and two red horse figurines on a teal wall

Nested diamond frames turn a few slats into wall art that also holds things. The gray washed wood sits softly on a teal wall, and the small shelves inside carry a row of tiny wooden houses, a patterned pot and two red horse figurines. Geometry suits a modern boho room, where it balances round lamps and soft textiles.

Cut every frame piece at 45 degrees so each diamond closes tightly, then glue the joints and pin them with small brad nails. Add the shelves where the inner frames meet the outer one. This is a light display shelf, so keep heavy books elsewhere and hang it on two fixings so it stays level.

58. Leaning Pallet Christmas Tree

Triangular Christmas tree made of horizontal pallet slats on a central post with a block base, decorated with hand painted ornaments and a star

For small apartments or homes with curious pets, a flat Christmas tree saves floor space and survives any wagging tail. Horizontal slats of decreasing length are screwed to a central post that stands in a block base, and painted glass ornaments hang from small hooks under each slat with a star at the top.

Cut each slat a little shorter than the one below and center it on the post with a pencil line. Leave the wood natural for a Nordic look or wash it white for a snowy one. A small bracket or picture hook at the top keeps the tree from sliding off the wall, and after the holidays it stores flat behind a wardrobe.

59. Wall of Flower Crates

Four small burgundy slatted pallet crates mounted on a stained wooden post against a dark green wall, each holding a vase of flowers

Four small crates mounted on a dark wooden post make a vertical vase display for a dining nook or a narrow wall by a window. Painted burgundy against a deep green wall, they create a moody, jewel toned corner, and each crate can hold a different flower as the seasons change.

Build the crates from narrow slats with a solid floor, screw them to the post from behind and fix the post into studs. Always put the flowers in a vase or a waterproof liner so no water reaches the wood. For more ideas built around small boxes, the wooden crate decorating ideas are a good next stop.

60. Living Room Divider with a Climbing Planter

Freestanding pallet room divider of upright pallets with pothos climbing up the slats from a long planter box at the base, beside a gray sofa

Upright pallets with a long planter box at their feet become a living screen between the sofa and the hallway. Pothos climbs the slats and spills over the box, softening a modern room and adding privacy without the weight of a solid wall.

Line the planter with a heavy plastic liner or use plastic troughs inside it, so damp soil never sits against the wood. Tie the vines to the slats with soft plant ties as they grow. A tall divider must not depend on the planter alone for balance; fix the top to the ceiling or to a wall with a bracket. Pothos is toxic to cats and dogs, so think twice if pets share the room. Other ways to grow upward indoors are collected in these indoor vertical garden walls.

Safety Notes for Pallet Furniture

Start with the wood itself. Bring home only pallets with a clear HT, DB or KD mark, leave anything stamped MB, and avoid unmarked, stained or moldy pallets for beds, children's furniture and anything near food. Never burn pallet offcuts indoors or in a stove, since you cannot be sure what the wood has absorbed during its working life.

Protect yourself while you work. Wear safety glasses, gloves and closed shoes while breaking pallets down, because nails snap and fly. Sand outdoors or with dust extraction and a fitted dust mask, and pull or punch out every nail before running a saw or sander over a board.

Fix tall and heavy pieces to the wall. Bookcases, wardrobes, room dividers, wall racks and anything a child might climb need an anti tip strap or bracket screwed into a stud or into masonry with the right plugs. Shelves that carry books, jars or weights need closely spaced supports and brackets, not nails. Overhead parts, such as a bed canopy or a bridge cabinet above a headboard, must be bolted rather than simply resting in place.

Children's pieces need extra care. On anything a baby or toddler sleeps in, plays in or climbs, keep slat gaps no wider than about 2 3/8 inches (6 cm), fit mattresses snugly with no side gaps, round every edge and choose paints and clear coats labeled safe for toys. Use acrylic or safety backed mirrors, keep cords and long garlands away from beds, and check screws for loosening every few months, since children test furniture harder than adults do.

Choose the right glass, wheels and finishes. Use tempered glass for tabletops, locking casters for anything on wheels and waterproof glue with a water resistant sealer in bathrooms and entries. Let every finish cure fully before heavy use, and give finished pieces a few days of fresh air before they go into a bedroom.

Keep plants and pets in mind. Pothos and many other trailing houseplants are toxic to cats and dogs, so place them out of reach, and always use a liner or saucer so water never soaks into the wood, where it can lead to mold and soft spots.

Handled this way, a free pallet becomes furniture that carries books, children and Sunday naps for years. If you enjoy giving old timber a second life, the reclaimed wood projects are a natural next read.

Get New Decor Ideas by Email

Fresh DIY projects, cozy styling ideas and seasonal decor inspiration, sent to your inbox from time to time. No spam, and you can unsubscribe whenever you like.

We only use your email to send Decovive updates. See our Privacy Policy.

Related Articles

Leave a Reply

Follow us on Pinterest @decovivehome